Mounting a Transducer

Without a transducer your fishfinder is useless as it is the transducer that sends the signal through the water to receive the pictures on the fishfinder screen. Equally important is mounting the transducer correctly and in the best location on your boat so you get optimum signal performance.

 

Mounting Methods

There are 3 types of transducer available that require different mounting methods depending on what type of boat you have or which particular mount you choose to use. Each method has its pros and cons - consider first what option would suit your style of boat:

 

Transom Mount Transducer
transom mount transducerTransom mount transducers are obviously mounted directly on the boats transom at the stern of the boat. The transducer needs to be located in the water and usually just below the level of the hull. Transom mount transducers are usually plastic, are the most common type used and are the cheapest of the transducer types available.

transom mount transducerThe recommended overall size of a boat with a planing hull using a transom mount transducer is less than 30 feet. Typically these types of boats are those with outboards, inboard-outboard and jet drives. They are not recommended for large or twin screw inboard boats as the aerated water from the propeller will reduce performance. They are also not recommended for use at very high speed.

A transom mount transducer should be tilted slightly forward (down towards the bottom) when the boat is in the water so that as the boat moves there is a smooth flow of water running across it. A transom mount transducer can be angled from 3 to 16 degrees if required.

Advantages:

Easy to install
East to maintain and clean
Inexpensive

 

Disadvantages:

1. The performance is not as good as a thru-hull
2. Normally used with smaller boats

 

Thru-Hull Transducer

thru hull transducerThru-Hull transducers protrude directly into the water via a hole drilled in the bottom of the boat. Thru-hull transducers are considered to give the best performance but also are the most expensive. Thru-hull transducers are recommended for displacement hull boats with straight shaft inboard engines.

thru hull transducer diagramThru-hull transducers must be positioned in front of the rudder, propeller, keel or anything else that may cause turbulence that will impair the transducers performance. They should also always be mounted in the water and angled downwards. A fairing block will also be required to aid proper mounting to keep the transducer perpendicular to the bottom.

Advantages:

Give best performance
Can be used at fast speeds

Disadvantages:

Require a hole cut in the hull
Require a fairing block
More maintenance required (can get dirty and fouled up)

 

In-Hull Transducer

in-hull transducerIn-hull or shoot-thru transducers are stuck to the inside of fibreglass hulls, they will not work with aluminum, wood or steel hulls or with hulls that have foam padded pockets. Any wood, metal or foam layers on top of the fibreglass hull will need to be removed in order for the in-hull transducer to work.

in-hull transducer photoIn-hull transducers are far less effective than transom mount or thru-hull because the signal needs to be transmitted and received through the hull of the boat. Fibreglass hulls can often be reinforced with areas of foam or balsa wood for extra strength. It is these areas that will need to be avoided when locating a position for an in-hull transducer, because balsa and foam are very poor sound conductors.

Advantages:

Inexpensive
No need to cut a hole in the hull
Avoids obstructions in the water
Virtually maintenance free

Disadvantages:

Reduction of maximum depth capability
Fish detection is impaired
On Fibreglass hulls can be used

 

Installation of a Transom Mount Transducer

Main steps:

1. Find the best transducer mounting location

2. Prepare the mounting location

3. Assemble the transducer and perform the initial mounting steps

4. Route the Transducers Cable through the boat

5. Connect the Transducer Cable to the transducer

6. Test the Transducer

 

Explanation video of best location for mounting a transom mount transducer

 

1. Find the best transducer mounting location

transom turbulence areasOne of the most important factors in finding the best transducer mount location is to avoid turbulence. As a boat moves through the water turbulence is caused from the weight of the boat and from the propeller. The turbulent water is far stronger immediately behind strakes, ribs, or rows of rivets on the underneath of the boat, and also in the area immediately around the propeller. Propellers running clockwise create more turbulence on the port (left) side of the boat. If your boat uses an outboard it is best to locate the transducer at least 15" away from the propeller (to the side).

 

 

transom mount turbulenceThe easiest way to find a turbulence free area on your transom is while the boat is moving. If you intend using your fishfinder at fairly high speeds, then this is the best method, otherwise select a location where the hull is smooth and flat and free of ribs or other such protusions.

 

 

 

 

transom mount turbulenceOn boats that have stepped hulls, it is possible to mount the transducer on the step. Avoid mounting the transducer behind a step otherwise the transducer could get pop out of the water under high speed - the transducer must remain in the water to maintain the sonar signal.

 

 

 

It may not be possible to find a turbulence-free area of water behind the transom near the propeller. In this situation you may have to consider the other mount types - In-Hull or Thru-Hull.

If you are carrying your boat on a trailer make sure that the transom mount transducer is not in an area where it can be damaged to any part of your trailer - especially as you are launching and loading the boat back on the trainer.

 

2. Prepare the mounting location

There will be variations for fitting different models of fishfinder and their transom mount locations. This example is based on the Humminbird 898csi.

You will need to carry out the installation out of the water. It is near impossible to install a transom mount transducer while the boat is in the water. You will need to drill holes so this could be impracticle as well as dangerous (if using an electric drill). The instructions here assume your boat is sitting on a trailer on dry land.

For best results ensure that the boat is level in every direction sitting on the trailer. Use a spirit level to test and adjust this until it is at the optimum level both ways.

 

transom bracket diagramWhile holding the mounting bracket on the area you have selected to mount it, use the level and make sure the lower corner of the bracket does not extend past the bottom of the hull. You should also make sure there is at least 1/4" clearance between the bottom of the bracket and the bottom of the transom for fibrelgass boats, and 1/8" clearance for aluminum boats.

 

 

 

 

transom bracket hole mount

 

 

While holding the bracket in place mark the two drill holes with a pencil near the top of the slot - ensure that each hold is centred.

When drilling it is important to make sure the drill is perpendicular with the transom and not parallel to the ground.

 

 

 

3. Assemble the transducer and perform the initial mounting steps

 

transducer pivot arm

 

 

 

Most transom mount type transducers will have a pivot bolt that needs to be inserted through the pivot arm and assembly bracket. Hand tighten the pivot bolt then insert the pivot arm assembly into the mounting bracket.

 

 

 

 

transducer mount to transom

 

 

 

Screw the assembly bracket to the transom, but not too tight initially, as you may need to slide it to adjust to the correct position.

 

 

 

 

 

 

transducer rachet adjustment

Transom mount transducers often have a ratchet adjustment to enable correct positioning of the angle of the transducer. This should be adjusted so that it is parallel and just below the hull of the boat.

 

 

transom angle adjustment

 

 

4. Route the Transducers Cable through the boat

 

The transducer cable will usually be routed through the boat via a hole in the transom. Ensure that you leave enough slack cable so that the transducer head can be adjusted at all possible angles. Fix a cable clamp (usually supplied) to the outside of the transom so that transducer head cannot be moved in the even of the cable being pulled from within the boat. The hole can be sealed with a waterproof silicon once fitted to ensure it is watertight.

transducer cable through transom

Most manufacturers will also recommend NOT cutting, or shortening the cable - special transducer cable extensions are available from the suppliers (not usually supplied). Also the cable should be placed away from any interference such as VHF radio. The recommended length of cable is up to 50' max.

 

 

 

 

 

 

 

5. Connect the Transducer Cable to the transducer

Plug the cable into the transducer control head (fishfinder receiver). The cable head will usually only plug in one way to prevent reversed installation, so do not force the connector or you will damage the pins. Part of the cable will need to route to your battery of power supply. Ensure you connect the poles correctly usually RED (Positive +) and BLACK (Negative -).

 

6. Test the Transducer

Power on the fishfinder and ensure that you get a reading through the control panel screen. You may need to adjust the angle of the transducer. Go for a gentle run in the boat and adjust as necessary. Once you get a reasonable reading increase your speed and ensure the readings remain consistent. Adjust the transducer angle as necessary for your maximum desired speed. Once everthing is working satisfactorily then tighten the screws and bolts and silicon the holes and screws.

Leave a Reply